[0x10105002]romcode/initialize Ddr/read Initialize Status/usb Control Setup Error

You are using an out of date browser. It may non brandish this or other websites correctly.
You should upgrade or apply an culling browser.

• #1

HI,
i have Amilogic M805, Wifi is AP6212
on the board is: Netxeon MK808Q_V10-20140822
On the cover is MINI TV form android Quad - Cadre MK808B Plus

If i tried USB_Burning_Tool
I have mistake [0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
Why ?

• #2

How-do-you-do,
i take Amilogic M805, Wifi is AP6212
on the board is: Netxeon MK808Q_V10-20140822
On the comprehend is MINI Idiot box form android Quad - Core MK808B Plus

If i tried USB_Burning_Tool
I have error [0x10105002]Romcode/Initialize DDR/Read initialize condition/USB Control setup mistake
Why ?

I had the same problem with S905 when use defective usb flashing cable. and effort redownload firmware

• #3

I had the same problem with S905 when employ defective usb flashing cablevision. and try redownload firmware

i endeavour 2 cables and 2 computers
windows 10 64bit
a windows xp 32bit

same mistake.

• #4

I had same trouble with M8S android box, through trial and mistake and an hour of pulling my hair out, I tried this, Amlogic burning tool, Toothpick method and male to male usb cablevision. (Go out toothpick in AV hole )Afterwards releasing the toothpick and pressing showtime the mistake comes up later on 2% I quickly pressed the toothpick in again to come across what would happen and smash information technology started to burn the firmware on, perhaps luck i dont know but box support running.. Hope information technology works for others..Des

• #v

how y'all prepare that fault? Romcode/Initialize DDR/Read initialize status/USB Control Setup Error

• #six

Aforementioned problem with MXIII 4k =(

• #7

Had the same problem, shortened the USB cable (that i made myself) to 15Cm, then information technology worked, indicate integrity ?

• #eight

first put the rom y'all will use, then press start, only and then plug the device into the USB port. Worked with me having the same issues.

• #9

work for me... redownload firmware

• #10

Code4power, a link please for download the img

• #11

Had same outcome with MXS Plus unit.... Tried a different USB-USB cable and at present up and running. MANY Thanks TO ALL ON Here

• #12

uncheck erase flash and bootloader in amlogic tool and that should fix your problem

• #13

uncheck erase flash and bootloader in amlogic tool and that should fix your problem

Worked similar a charm. Thanks

• #fifteen

I cannot go by that error. I take tried iii unlike computers and various different versions of the burning tool every bit well as unchecking the boxes suggested above. Then frustrating.

• #16

x96pro +

I cannot get past that error. I have tried 3 different computers and diverse unlike versions of the called-for tool as well as unchecking the boxes suggested higher up. So frustrating.

I had the same issues every bit described above, and I simly just changed the cable lenght from 1.5m to 30cm and the box started flashing itself from the burning tool!

• #17

I got a shorter cable merely information technology notwithstanding does it for me

• #xviii

And then guys later going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your paradigm to USB burning tool (don't hit showtime) - connect USB A to A cable (didn't connect) - Wink Pins v-6 or six-7 - Now USB tools come across's the box but don't striking start even so - considering usb ability is not enough to burn down it - Now insert the toothpic to hitting the reset push - Now connect ability while toothpic is inserted - Viola - the box starts burning - This is a sure to work method - everytime.

• #19

So guys afterwards going crazy did this - Tried the Nand Method on a95x. Sequence - Upload your epitome to USB called-for tool (don't hitting start) - connect USB A to A cable (didn't connect) - Flash Pins v-vi or 6-7 - Now USB tools see's the box but don't striking start yet - considering usb power is not enough to fire it - Now insert the toothpic to hitting the reset button - Now connect power while toothpic is inserted - Viola - the box starts burning - This is a sure to work method - everytime.

Dear, i tried this method as well...just no luck. delight communication..., if possible please share the link for usb called-for tool and the firmware for MXQ PRO+ model. Will try fresh. Would highly appreciate ur assistance...

• #20

Had the same problem with mecool km9.
Tried all with no luck, then i tried to disconnect the box, shut so restart usb burning tool, load the img file, unchecked erase flash and erase bootloader, concur the reset button with toothpic, then connect the box, hit refresh, and after that, start the flashing process.
Then, if you tried to uncheck erase... like i did, y'all should try to disconnect the box, every bit it doesn't seem to register the unchecking without that.
:skilful:

You can run across how many failed i had before disconnecting/reconnecting the box !

Similar threads

lefflerconifice.blogspot.com

Source: https://forum.xda-developers.com/t/usb_burning_tool-error.3321735/

Share this post